Products

CFR-WB2™

High performance, water-based concrete form release agent and bold breaker.

Clear

Aluminium and steel concrete form release, for tilt slabs, medium complexity moulds and small to medium diameter pipes. Water based.

Product Technical Benefits:
  • Clean release characteristics, low dusting.
  • Water based emulsion – contains no solvents or hydrocarbons.
  •  Safe and non-hazardous to personnel.
  •  Designed for use with steel, aluminium and film faced wood forms/moulds.
Product Applications
  •  Tilt slabs.
  •  Medium complexity moulds.
  • Medium diameter pipes, up to 50cm diameter.
  •  Also acts as slab-on-slab bond breaker.
How to Use

MOULD PREPARATION
1)  Ensure the mould is thoroughly clean before using CFR-WB2TM:

a)  Scrub the mould using a degreaser / solvent / purposed made cleaner, with a brush / non-scratch scrubbing pad, then polish off all residue with absorbent cloths before it dries.
b)  Repeat as necessary until mould is thoroughly clean and allow to dry fully.

2)  Conditioning clean mould: Depending on the grade, finish and condition of the mould / form it might be necessary to apply a precoat of CFR-WB2TM and allow it to dry, then apply a second coat as the mould release agent. This is only for the first pour.

3)  Cleaning the mould between pours: After each pour thoroughly remove all dry concrete residue / dust using brushes, cloths etc, paying attention to corners, nooks and crannies, before CFR-WB2TM is applied for the next pour.

HOW TO APPLY
1)  Apply CFR-WB2TM with an airless sprayer, which achieves a fine mist and allows even coating of the surface.
2)  Ensure all of the mould / form surfaces are covered with an even, thin coating of CFR- WB2TM.
3)  Be careful to avoid concentration or pooling of the product or drips. On vertical surfaces do not over-apply – so you avoid the product running or dripping.
4)  After application allow the product to dry fully. Drying time depends on ambient temperature and humidity. Once a clear film is left on the mould, the mould is ready for concrete.
5)  NOTE – It is highly recommended to experiment with mould surface preparation, spray application and drying time to achieve the best result before tackling a large project.

Pack Sizes
  • 20L (5.3GAL); 200L (53GAL)
Precautions

Avoid ingestion. Avoid inhaling. Avoid contact with eyes.
IMPORTANT: For the full health and safety hazard information and how to safely handle and use this product, make sure that you obtain a copy of the Safety Data Sheet (SDS) from Chemforce office or website.

First Aid

If inhaled relocate to fresh air. If symptoms occur, seek immediate medical attention.
If contact with eyes occurs, wash eyes with copious quantities of water and consult doctor if irritation persists.
If ingested (swallowed) DO NOT induce vomiting. Get medical attention if symptoms occur. Rinse mouth thoroughly with water.

For advice, immediately contact a doctor, ambulance, or, a Poison Information Centre:
Australia – 13 11 26 (Australia Wide)
USA – American Association of Poison Control Centres 1-800-222-1222
Canadian Poison Centres – Ontario (24/7): Telephone: 416-813-5900; Toll free: 1-800-268- 9017

UK – England and Wales: NHS 111 – dial 111; Scotland: NHS 24 – dial 111; Republic of Ireland: 01 809 2166

Accidents

Spillage – Take up mechanically or with absorbent material such as sand, earth or vermiculite.

Transport

TDG UN Status: This material is not regulated hazardous material for transportation.

Shelf Life and Storage Guidelines

Shelf life is 4 months from the date of delivery.
Storage temperature should be within the range of 5 to 32C (40-90F) Containers should be well sealed.

Technical Data
  • Specific Gravity: ~0.99
  • Colour: Milky white to yellowish
  • Weight: 20L (5.3G) = 20.5Kg (45Lb), 200L (53G) = 215Kg (474Lb).
  • VOCs: Zero
Country of Manufacture

Australia

SKU: N/A Categories: , Tags: , ,

Subscribe to our Newsletter

  • This field is for validation purposes and should be left unchanged.